Icynene Blown In Insulation Nationwide

Icynene Blown In Insulation in Pasadena: What to Know First

We provide independent Icynene blown in insulation repair, removal, and installation across Pasadena. Most Icynene jobs run $1,400 – $4,200 depending on attic square footage, current R-value, and how much of the old material needs to come out. Same-week scheduling is standard, and we arrive with a written price before any tool comes off the truck. This page is for Pasadena homeowners who own a home with Icynene spray foam or blown-in product and need straight answers about what’s failing, what it costs to fix, and how fast we can get it done. Call (626) 628-2368 and you’ll get a real person, not a voicemail.

Call (626) 628-2368

How Icynene Products Fail – and How We Fix Them

Icynene makes open-cell spray foam (Classic and Classic Max) and closed-cell spray foam (ProSeal and ProSeal LE). Most Pasadena homes with “Icynene blown in insulation” fall into one of two categories: either a previous contractor sprayed Icynene foam and then topped it with blown-in fiberglass or cellulose, or the homeowner has loose-fill in an attic that also has Icynene around the rim joists or roofline. Here’s what we actually find in Pasadena attics:

• Shrinkage in Icynene Classic around attic can lights and penetrations. Classic is a light-density open-cell foam, and in Pasadena’s dry, hot summers we see it pull back from framing members it was sprayed against. That creates gaps where conditioned air leaks into the attic. We remove the separated foam, air-seal the penetration properly, and re-insulate the area with blown-in product matched to the existing R-value.
• Moisture trapping under Icynene ProSeal when a roof leak goes unnoticed. Closed-cell foam is a vapor barrier. When water gets between the foam and the roof deck, it sits there. We’ve pulled ProSeal off Pasadena roof decks and found rot the homeowner had zero clue about. If the foam is wet, it has to come out before any new insulation goes in. We don’t blow over wet anything.
• Crushed or displaced blown-in insulation after a contractor worked in the attic. This is the most common one. An electrician, plumber, or cable installer moves blown-in fiberglass aside to work and never rakes it back. The homeowner doesn’t know until their summer electric bill spikes. We level the coverage, top it off to the target R-value, and document the final depth with photos.
• Incompatible layering: blown-in fiberglass over Icynene Classic Max that never fully cured. Classic Max has a faster rise and a softer cell structure than standard Classic. If it was sprayed in cold weather (yes, Pasadena gets 40-degree nights in January), it may not have cured properly before blown-in was dumped on top. The result is a spongy, uneven mess. We remove both layers and start clean.
• Rodent damage running through Icynene and the blown-in product above it. Rats in Pasadena attics tunnel through open-cell foam like it’s a hotel. Once they’ve gone through Icynene, they’ve also contaminated the loose-fill on top. This requires full removal, sanitizing, air sealing, and then fresh blown-in insulation. We’ve done this exact job on dozens of homes from Bungalow Heaven to San Rafael Hills.

Our Icynene Blown In Insulation Process

Every job follows the same sequence. We don’t improvise in your attic, and we don’t skip steps just because it’s hot up there.

1. 1
   Call and schedule. A live person answers 24/7. We book a specific window, and our technician arrives inside it, in uniform, background-checked.
2. 2
   Attic inspection and measurement. We check current R-value, identify what’s Icynene and what’s not, look for moisture, air leaks, and any boards or wires that need to be worked around. You get the findings in plain English.
3. 3
   Written price. Before any work starts, you approve a dollar figure on paper. That number is the number on the invoice.
4. 4
   Removal (if needed) and air sealing. If old Icynene is wet, infested, or failing, we remove it. Then we seal penetrations: can lights, top plates, plumbing chases, duct boots. This is where most insulation jobs fall apart, and we spend the time here.
5. 5
   Blown-in installation. We blow to the R-value we agreed on, typically R-38 to R-60 for Pasadena attics depending on your home’s age and HVAC setup. We level the coverage and verify depth across the whole attic, not just the area near the hatch.
6. 6
   Final check and guarantee. We walk you through photos of the finished attic. Every job carries the 365-Day Done Right Promise in writing. If the work fails within a year, we come back at no charge.

What Icynene Blown In Insulation Costs in Pasadena

Blown-in attic insulation in Pasadena typically runs $1.75 – $3.50 per square foot depending on R-value target and prep work. Here’s what that looks like for common Icynene scenarios:

• Top-off over existing blown-in, no Icynene removal: $1,200 – $2,200 for a 1,200 sq ft attic
• Partial Icynene removal plus new blown-in: $2,500 – $4,200 depending on how much foam has to come out
• Full removal (contaminated, wet, or rodent-damaged): $3,500 – $6,500 for a typical Pasadena attic
• The biggest variables: access (steep roofs and tight attics cost more), how much old material must be bagged and hauled, and whether we find damage under the foam that needs a separate contractor.

We give you the number before we start. Not an estimate with fine print. A written price. Call (626) 628-2368 and we’ll schedule an attic inspection. The inspection is free, and you’ll have real numbers the same day.

Why Pasadena Homeowners Call Alden Insulation Pasadena for Icynene Work

We’re part of the Garrison Partners family, established 2002, and every Alden location operates under The Garrison Standard. That’s not a marketing phrase. It means a written price before the job, a background-checked technician who shows up when we said, and a 365-Day Done Right Promise in writing on every job. If the insulation work fails within a year, we come back and make it right at no charge. No callbacks billed as “service fees.” No arguing about whose fault the failure was.

Bryce Holloway, our owner, has been doing insulation work across the San Gabriel Valley for the better part of two decades. He and the crew have pulled apart Icynene, Owens Corning, Johns Manville, Knauf, Rockwool, CertainTeed, Demilec, GreenFiber, and Reflectix, so when we recommend a material or a fix for your Icynene setup, it’s because we’ve seen what works and what doesn’t in Pasadena’s dry heat and cool canyon nights. Seal it right the first time – the attic doesn’t give second chances.

FAQs