Demilec Blown In Insulation Nationwide

Demilec Blown In Insulation in Pasadena: What to Know First

We install, repair, and remove Demilec blown-in insulation throughout Pasadena as an independent Demilec service provider, not a manufacturer-authorized dealer. Most Demilec blown-in jobs in Pasadena run between $1,800 and $4,200 depending on square footage, current R-value, and whether old insulation needs to come out first. We give you a written price before any work starts, and every job carries our 365-Day Done Right Promise in writing. If you’re a Pasadena homeowner with a Demilec attic that isn’t holding temperature the way it should, call (626) 628-2368 and we’ll take a look.

Call (626) 628-2368

This page is for homeowners who already have Demilec insulation in their attic, or who are considering it and want straight answers on how it performs in Pasadena’s specific climate. Bryce Holloway and our crew have worked on Demilec jobs across the San Gabriel Valley for the better part of two decades, and we’ve learned exactly where these products excel and where they need extra attention.

How Demilec Products Fail, and How We Fix Them

Demilec makes quality insulation. But every product has weak points, especially in a climate like Pasadena’s, where dry summers hit triple digits and canyon nights drop fast. Here’s what we actually see on Demilec blown-in jobs:

• Heatlok HFO settling in vented attics. Heatlok HFO is technically a spray foam, but many Pasadena homes pair it with blown-in layers on top for extra R-value. The problem: over five or six summers, the foam’s thermal cycling can cause micro-separation from the decking, and the blown-in layer drifts into the gaps. We find this constantly in homes near Eaton Canyon, where temperature swings are dramatic. The fix is removing the compromised section, re-sealing the gap, and reinstalling blown-in at the correct depth. Skipping the re-seal step just means doing it again in two years.
• Sealection 500 shrinkage near recessed light housings. Sealection 500 is a common open-cell line we see in Pasadena attics, especially in homes built in the 1980s and 1990s. Around can lights, the foam dries and pulls back over time, leaving a half-inch channel where heat escapes straight into the attic. Homeowners notice it as a warm spot on the ceiling directly above the fixture. We pull the housing clearance, re-install the foam properly, and put a dam-approved cover over the light before re-blowing the surrounding area.
• Lapolla-brand blown-in (Demilec’s parent line) compressing unevenly. Demilec’s blown-in fiberglass and cellulose, branded under the Lapolla and Demilec names, compresses over time in Pasadena’s low humidity. Fiberglass loses loft faster here than in coastal climates because the air is so dry. We regularly find attics where the original install was R-38 and the actual coverage measures R-19 after seven years. The fix is a top-off and a depth assessment at the eaves and center bay, not just a visual check.
• Moisture wicking in Demilec cellulose near bathroom vent terminations. When a bathroom fan terminates in the attic instead of through the roof, Demilec cellulose soaks up the moisture and mats down. This is a Pasadena code issue as much as an insulation issue. The insulation loses its air pockets, and you end up with a damp, compacted layer that does nothing. We re-route the vent to terminate outside, replace the damaged insulation, and air-seal the penetration before blowing new material in.
• Pest intrusion in Demilec blown-in layers. Squirrels and roof rats are a fact of life in Pasadena attics, particularly in older neighborhoods like Bungalow Heaven and around the Arroyo. They tunnel through blown-in insulation, compress it, and leave waste behind. We remove the contaminated material, seal entry points at gable ends and soffits, and re-blow at the proper depth. Without the exclusion work, you’re just refilling a rodent highway.

Our Demilec Blown In Insulation Process

Here’s how a Demilec job goes from first call to final walkthrough:

1. 1
   Call and schedule. You reach a live person at (626) 628-2368, day or night. No voicemail tree, no call center. We schedule inside a specific window, not a half-day range.
2. 2
   Inspection and measurement. A uniformed, background-checked technician goes into the attic, measures current R-value at multiple points, and checks for the specific Demilec failure modes we listed above. We look for air leaks, settling, moisture, and pest damage.
3. 3
   Written quote. We hand you a written price before any equipment comes off the truck. The number you approve is the number on the invoice. No surprises.
4. 4
   Removal and prep. If old Demilec material is compromised, we remove it with commercial vacuums, then air-seal penetrations: top plates, can light housings, plumbing stacks, and vent terminations. This is the step most contractors skip, and it’s the step that makes or breaks a blown-in job.
5. 5
   Blow-in at correct depth. We install Demilec blown-in insulation at the depth required to hit the R-value you’re paying for, not the depth that looks good from the hatch. We use depth markers and verify coverage at the eaves, where Pasadena attics are almost always under-insulated.
6. 6
   Final check and written guarantee. We verify depth coverage, confirm the attic hatch is sealed, and hand you a written 365-Day Done Right Promise. If anything fails within a year, we come back free.

What Demilec Blown In Insulation Costs in Pasadena

Here are honest numbers for the Pasadena market. These aren’t teaser prices; they’re what we see on real jobs:

What moves the price: attic height and access, how much old material has to come out, whether we find air leaks that need sealing, and how far the eaves are from the working space. Every quote is written, and it’s free. Call (626) 628-2368 and we’ll give you a number you can hold us to.

Why Pasadena Homeowners Call Alden Insulation Pasadena for Demilec Work

Alden Insulation Pasadena is independently owned and operated, held to The Garrison Standard, which means written prices, written guarantees, and a background-checked crew that shows up inside the window it promised. We’ve been doing this since 2002, and the 365-Day Done Right Promise applies to every Demilec job we touch. If the work fails within a year, we come back at no charge. That’s not a sales line. It’s on paper.

We install Demilec alongside products from Owens Corning, Johns Manville, Knauf, Rockwool, CertainTeed, Icynene, and GreenFiber, plus Reflectix for specific radiant barrier applications. So when we tell you Demilec is the right product for your attic, it’s because it actually is, not because it’s the only thing we carry.

Bryce Holloway grew up in Los Angeles and learned the trade at Los Angeles Trade-Technical College before spending nearly two decades doing insulation work across the San Gabriel Valley. He’s been in attics from century-old bungalows near the Pasadena Civic Auditorium to newer builds in Arcadia, and he knows how Pasadena’s dry summers and cool canyon nights stress an attic. Seal it right the first time. The attic doesn’t give second chances.

FAQs